How to Coat Screens with the Baselayr Wall Mounted Screen Coating Rack

How to Coat Screens with the Baselayr Wall Mounted Screen Coating Rack  | Screenprinting.com

Ryonet Team |

KEY TAKEAWAYS

  • The Baselayr Wall Mounted Screen Coating Rack gets screen frames off the floor and locks them rigid against the wall for repeatable emulsion-over-mesh (EOM) deposits.
  • Securing the frame in place frees both hands to grip your scoop coater, reducing physical strain on your back and shoulders during long darkroom shifts.
  • Engaging the toggle lever to 90 percent before tightening the hand knobs lets you finish at 100 percent lock for zero frame flex.
  • An integrated 20-inch top shelf holds your loaded scoop coater safely while you release the clamp and flip screens between passes.
  • Proudly made in the USA, the sliding crossbar adjusts without tools to fit screen frames from 6 inches to 36 inches tall.

Consistent emulsion coats with less physical strain on your body start with how you hold your screens in the darkroom. Balancing a frame with one hand while applying pressure to a scoop coater with the other forces awkward posture and leads to uneven edges, streaks, and thin spots across your mesh. Mounting the Baselayr Wall Mounted Screen Coating Rack gets your screens off the floor and locked solid into position so you can focus on angle, pressure, and coating speed.

Watch the walkthrough video below to see how quick it is to clamp a screen, pull smooth two-handed emulsion passes, and flip frames using the built-in storage shelf.

HOW TWO HANDED COATING IMPROVES STENCIL CONSISTENCY

Stencil performance on press comes directly from your prepress routine in the darkroom. When liquid emulsion varies in thickness across the mesh, exposure times become unpredictable. Thin zones break down early during production runs, while thick emulsion pools hold moisture and create pinholes.

Because the Baselayr Wall Mounted Screen Coating Rack holds your frame completely stationary, you can grip your Dual Edge Emulsion Scoop Coater firmly with both hands. Two-handed control lets you apply even pressure from edge to edge and pull slowly upward at a steady pace, building a uniform EOM profile across the entire printable area. Pair that stability with reliable photopolymer formulas like Baselayr Complete Emulsion or Baselayr Long Lasting Emulsion to hold fine halftone details cleanly through washout.

Screen printer pulling a smooth two-handed emulsion pass on a screen clamped in the Baselayr Wall Mounted Screen Coating Rack

STEP BY STEP HOW TO COAT A SCREEN ON THE BASELAYR RACK

Once your rack is mounted to wall studs or heavy-duty anchors at a comfortable chest-to-shoulder height, coating a batch of screens takes only a few repeatable motions. Follow this exact sequence shown in the video:

  1. Clear the Top Clamp Loosen the four-arm phenolic knobs on the sliding crossbar and move the upper clamp assembly up out of your way.
  2. Seat the Screen Frame Rest the bottom edge of your screen inside the lower holding channel with the shirt side (print side) facing toward you.
  3. Set the 90 Percent Clamp Position Slide the upper crossbar down until the top clamp lip meets your frame, then engage the red toggle lever to about 90 percent.
  4. Lock the Crossbar Knobs Tighten both phenolic hand knobs firmly onto the dual vertical aluminum rails to lock your frame height in place.
  5. Engage Full Clamping Tension Push the toggle lever down all the way to 100 percent to lock the frame completely rigid against the wall.
  6. Pull Your Print Side Coat Load your scoop coater with emulsion, grip it with both hands, place the edge against the bottom of the mesh with firm pressure, and pull slowly upward to the top for a smooth EOM layer.
  7. Stage Your Coater and Flip the Screen Set your loaded scoop coater onto the built-in 20-inch storage shelf, release the toggle clamp, flip the screen around, lock it back down, and pull your squeegee-side coat.

Close-up of a screen printer engaging the red locking toggle lever on the Baselayr Wall Mounted Screen Coating Rack

Releasing the toggle clamp and flipping the screen between coats takes only seconds. Because your loaded scoop coater rests securely on the top aluminum shelf, you never have to set wet troughs on dirty worktables or interrupt your coating rhythm.

Screen printer seating an aluminum screen frame into the Baselayr Wall Mounted Screen Coating Rack while scoop coater rests on the top shelf

BUILT FOR EVERY FRAME SIZE AND DARKROOM LAYOUT

Print shops regularly rotate between small pocket frames and oversized back-print frames throughout the week. Built on dual aluminum extrusions, the sliding crossbar on the Baselayr Wall Mounted Screen Coating Rack adjusts from 6 inches all the way up to 36 inches tall. You can switch between standard Baselayr 20x24 Aluminum Frames and larger Baselayr 23x31 Aluminum Frames in seconds without hunting around the shop for hand tools.

Mechanical toggle clamping also outperforms spring-loaded stands in humid darkroom environments. Heavy-duty toggle leverage locks your frame solid with zero springy pushback when you press a full coater against the mesh. Above the crossbar, the integrated 20-inch aluminum shelf keeps your scoop coaters elevated off dirty worktables, protecting precision aluminum trough edges from nicks and keeping stray lint out of wet emulsion.

Baselayr Wall Mounted Screen Coating Rack mounted on a darkroom wall next to Baselayr emulsion tubs and a screen drying rack

Using vertical wall space keeps your darkroom floor clear for screen carts, washout booths, and exposure units. Position your coating rack right beside your Baselayr Screen Drying Cabinet so freshly degreased screens move straight from Baselayr Emulsion Prep to coating, horizontal drying, and exposure on your Baselayr LED Exposure Unit.

TECHNICAL SPECIFICATIONS AT A GLANCE

Feature Specification and Description
Screen Height Range 6 inches to 36 inches tall (standard and custom frames)
Clamping Mechanism Heavy-duty locking toggle clamp for zero frame flex
Height Adjustment Sliding crossbar on dual vertical aluminum extrusions
Locking Controls Tool-free phenolic plastic four-arm knobs
Coater Storage Integrated 20-inch aluminum scoop coater shelf included
Lower Frame Support Textured grip lower holding channel to support frame base
Wall Mount Hardware 3 modular wall-mounting brackets included
Manufacturing Origin Proudly made in the USA

FREQUENTLY ASKED QUESTIONS ABOUT THE BASELAYR SCREEN COATING RACK

Which side of the screen do you coat first on a wall-mounted coating rack?
Place the screen into the lower channel with the shirt side (print side) facing toward you first. Pulling your initial emulsion passes on the print side builds your stencil profile proud of the mesh, then you flip the screen around to coat the squeegee side.

Why engage the toggle lever to 90 percent before tightening the crossbar knobs?
Engaging the lever to 90 percent sets the proper clamping gap against the top of your screen frame. Tightening the four-arm knobs at 90 percent allows the final 10 percent of lever travel to apply firm mechanical downward pressure without over-stressing the frame.

What screen frame sizes fit the Baselayr Wall Mounted Screen Coating Rack?
The sliding crossbar accommodates screen frame heights from 6 inches up to 36 inches tall, covering standard 20x24 inch and 23x31 inch aluminum frames as well as custom specialty sizes.

Does the rack include wall mounting fasteners?
The kit includes three modular wall-mounting brackets and extrusion assembly hardware. Because shop walls vary between wood studs, drywall, and concrete block, supply mounting screws or anchors matched to your specific wall construction.

LEVEL UP YOUR DARKROOM WORKFLOW

Get your screens off the floor, take the strain off your body, and lock down consistent emulsion coats on every single frame.

SHOP BASELAYR SCREEN COATING RACK
SHOP ALL BASELAYR DARKROOM EQUIPMENT